Видео

Me every single time that I do a DIY, 😂, you did a great job. And the next time of course hire someone.

What type of screw do you use? I’ve been searching for an hour

Very good explanation. Thanks

Excellent video very informative and he gets straight to the point and stays on point no unnecessary chit chat or no fluff thank you

Nice no frills video but IMHO you were working with those loose wires from the old breaker were a little too close to the live breakers directly above so I would shut those off too in an abundance of caution especially if you are new to this.

What are those white clips called that you used to anchor the pan to the studs? Wonderful video thank you!

Why no primer? Also, you can’t move the pipes inground the way you are on a table so it would more difficult to get some of these items in place.

You know why I don’t have power going to either stud on the fuse box and fuses are hood ?

Would be more helpful if you constrained the position of the existing pipe to demonstrate the real problem. Moving the existing pipes is not a valid demo.

Thank you

Celebrating 9 years of people making the same complaint comments about not using primer (not required with the red hot blue glue) and not securing the wood blocks down to better simulate the pipes being buried 🎉🎉🎉 hahaha oh man. Replying to the same comments over and over is always fun! Great helpful video thanks!

I do 4 90's. I don't trust gaskets in the ground

You made this 4 years ago and its still helping people appreciate it boss.

Very useful tips. Didn't hear you mention something the guy at the store told me and that's that the slip coupling has an "in" end and and an "out" because of the slip mechanism.Be sure to read the directions on the product and check the direction of the water flow before installing. (And as the link in the show notes says Christy's is an all in one primer/glue)

do you have to put paper down before the mortar bed? i have a raised foundation

Can we set the mortar on top of a rubber shower pan liner?

I like to prefill my filter before I put it on so it’s really easy to prime

Te aventaste un tiro o qué onda?

Why is your hand all cut up?

Did you do that with the wires still live

It would work better and simulate the actual experience if you had fixed the pipe mounts in the board you had them on instead of moving the two pipes around

Thank you for this! Can you put the links to the tool you used to get the first layer of paint off

Quick question can I just replace the whole shaft assembly cause I don’t have a grinder I can just go to my local junk yard thank you

You didn't use the slip couple the way it's designed for lol, you suppose to use it to slide on the pipe bc ypu can't spread the lines apart for the make in

Nice 👍🏼

thanks for the help! just did mine, took bout 30-45 minutes

Where did you get the steering wheel?

Excellent video. How long should I wait before walking on it to install wall board? Thanks, Dave

It was not in the link on the video at all I watched it three times

Hello Sir, I know that this video is four years old but can you please tell me where you bought it or which site you went to? Thanks

Great job on your video, can you please give me the information on where you found that rag joined? Thanks

Super helpful, spot on instructions. Thank you.

Primer, please!

How are you going to get your drain throat in at this point, since it wasn't already attached to the pan?

Dry pack, bedding compound. To wet.

What was the brand of shower pan do you recall?

Can I use planipatch for this mortar?

Thanks. Good video, but it needs more dog! What a buddy you've got there.

Algorithm comment

I’ve never heard of waxed construction paper. Does it go by a different name? Why can’t you use roofing paper?

I rolled my eyes at the foam...until he took it out. Brilliant. So many tricks. I got a million auto repair tricks. We need to work out a trade. I'm dying over here trying to install a shower for a 400lb old man that barely walks.

How do you fix loose screws in a hollow core door. No videos on that subject

Why not just kill the power to the whole thing? That way you can't possibly get popped

Did the air bag light come on? Mine did.

Great video thanks

Couldn't you jus disconnect neg batt post?

Spent $103 on filter is that a good price or bad price,

Thanks for this! I don't quite understand how the shims would work. If it's not level why wouldn't you just push the high side into the mortar more? And if you have to use a shim how does that work, do you actually pick the pan up out of the mortar then put a shim on top of the mortar. Wouldn't lifting it mess up the mortar base since you already jumped up and down to sink it in deep?

On the dry fit, would you get it level and then mark the studs so you would know once you install whether it is pressed down enough? THanks for the video

File down the inside of the coupling stops and then you can slide them in place.